u 1 w 2 p 3 1 4 c 5 1 6 0 7 0 8 m 9 c 10 l 11 1 12 g 13 b 14 configuration taping code capacitance tolerance ( 20%) rated capacitance (10 f) rated voltage (16v) series name type voltage mark for 6.3v is 6v . voltage capacitance lot no. x2 10 16v plastic platform 0.3 max. 5.4 +0.1 0.2 d 0.5 b 0.2 c 0.2 0.5 max. a 0.2 a 0.2 e 0.5 to 0.8 d a b c e 1.8 4.3 4.3 1.0 2.1 5.3 5.3 1.3 2.4 6.6 6.6 2.2 45 (mm) 6.3 3.3 8.3 8.3 2.3 8 wp series 5.5mml chip type, bi-polarized designed for surface mounting on high density pc board. applicable to automatic mounting machine fed with carrier tape. compliant to the rohs directive (2002/95/ec). chip type dimensions type numbering system (example : 16v 10 f) specifications category temperature range rated voltage range rated capacitance range capacitance tolerance leakage current tangent of loss angle (tan ) stability at low temperature endurance shelf life marking performance characteristics item 40 to +85 c 6.3 to 50v 0.1 to 100f 20% at 120hz, 20 c after 2 minutes' application of rated voltage, leakage current is not more than 0.05cv or 10 (a) ,whichever is greater. black print on the case top. measurement frequency : 120hz, temperature : 20 c measurement frequency : 120hz the specifications listed at right shall be met when the capacitors are restored to 20 c after the rated voltage is applied for 1000 hours at 85 c with the polarity inverted every 250 hours. after storing the capacitors under no load at 85 c for 1000 hours and then performing voltage treatment based on jis c 5101-4 clause 4.1 at 20 c, they shall meet the specified values for the endurance characteristics listed above. resistance to soldering heat the capacitors are kept on a hot plate for 30 seconds, which is maintained at 250 c. the capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20 c. wp rated voltage (v) tan (max.) 6.3 0.24 10 0.20 16 0.17 25 0.17 35 0.15 50 0.15 z 25 c / z+20 c z 40 c / z+20 c rated voltage (v) impedance ratio zt / z20 (max.) 6.3 4 8 10 3 6 16 2 4 25 2 4 35 2 3 50 2 3 rated ripple current (marms) at 85 c 120hz 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 0r1 r22 r33 r47 010 2r2 3r3 4r7 100 220 330 470 101 5 6.3 6.3 8 28 37 45 82 4 6.3 6.3 8 17 33 41 61 4 5 6.3 6.3 8 12 23 37 49 75 5 5 6.3 8 8 12 16 27 50 61 4 5 5 6.3 8 8.4 16 18 29 54 4 4 4 4 4 5 5 6.3 8 1.0 2.0 2.8 4.0 8.4 13 17 20 36 allowable ripple 0j cap. (f) v 6.3 1a 10 1c 16 1e 25 1v 35 1h 50 code capacitance change leakage current tan within 20% of the initial capacitance value 200% or less than the initial specified value less than or equal to the initial specified value capacitance change leakage current tan within 10% of the initial capacitance value less than or equal to the initial specified value less than or equal to the initial specified value rated ripple aluminum electrolytic capacitors case size d (mm) zp smaller frequency coefficient of rated ripple current coefficient frequency 50 hz 120 hz 300 hz 1 khz 10 khz or more 0.70 1.00 1.17 1.36 1.50 taping specifications are given in page 23. recommended land size, soldering by reflow are given in page 18, 19. please select un(p.104) series if high c/v products are reqired. please refer to page 3 for the minimum order quantity. cat.8100y
|
